Dd15 rocker shaft torque specs

There are two intake lobes 7 on the intake camshaft 2 per cylinder. The corresponding intake valves are opened by the intake lobes 7 and the intake rocker arm. There are two exhaust lobes 5 and one brake lobe 6 on the exhaust camshaft 1 per cylinder.

All information subject to change without notice. Install as follows: 1. If removed, install the air compressor gear to the air compressor shaft and secure with nut. Clean all foreign material from the mating surfaces of the air compressor and the cylinder block. Install a new O-ring on the air compressor hub and a new O-ring on the oil supply, and then install the air compressor on the cylinder block.

Dd15 rocker shaft torque specs

Views 77 Downloads 2 File size KB. The top thread section of the nu. All information subject to change without notice. If removed, install the air compressor gear to the air compressor shaft and secure with nut. Clean all foreign material from the mating surfaces of the air compressor and the cylinder block. Install a new O-ring on the air compressor hub and a new O-ring on the oil supply, and then install the air compressor on the cylinder block. If an incorrect bolt length too long is used, the cup plugs installed in the cylinder block can be pushed out into the gear train causing severe damage to the gear train. The correct bolt length is 35 mm 1. NOTICE: Ensure when the air compressor coolant lines are installed that there is an O-ring and an O-ring retainer installed on both ends of the coolant lines. Ensure that the air compressor retainer is installed on the coolant line and is pushed down to lock the lines onto the inlet and outlet ports to the cylinder block, fuel filter module and air compressor. A leak will occur if the lines are incorrectly installed and the coolant line retainer is not engaged in the locked position. If the O-ring or the coolant line retainers are missing or removed, replace the coolant line. Install the coolant supply and return lines to the air compressor. Install the air lines to and from the air compressor. Refer to OEM specifications.

Tabela de parede linha diesel.

Share your interactive ePaper on all platforms and on your website with our embed function. See Figure 4. See Figure 5. Refer to section 2. Refer to section Exhaust Lobe 2. Brake Lobe 3.

The rocker cover 2 is made of an aluminum or plastic material and uses an elastomer seal 1 which completely encloses the valve operating mechanism including the overhead camshafts, brake assemblies and the injector harness. Loosen the bolts 1 or stud bolts 2 if equipped and isolators 3 ; remove rocker cover. Mark the location of the stud bolts. The stud bolts must be replaced in their original location during installation. Blow dry with compressed air. Check the rocker cover, breather passage and seal for damage. Replace as necessary. Inspect the bolts. Replace if damaged.

Dd15 rocker shaft torque specs

Share your interactive ePaper on all platforms and on your website with our embed function. See Figure 4. See Figure 5. Refer to section 2.

Toro porono

AND NO. If removed, install the air compressor gear to the air compressor shaft and secure with nut. Model No: VS 1. More information. Atlas Front Input Change The following pages contain instructions for Atlas transfer case front input. When tipping the Cable Processor Module back, after removing the toggle arm pin , use extreme caution not to drop. Service Parts. Exhaust Rocker Arm Shaft Assembly 6. Cookie policy. Refer to OEM specifications. Using rocker arm lifter spacer Page 6 and 7: 7. SeeFigure Loosen the seven bolts securing the exhaust rocker shaft to the camshaft cap.

There are two intake lobes 7 on the intake camshaft 2 per cylinder.

Common rail system for nissan. Loosen the seven bolts securing the intake rocker shaft to the camshaft caps. Fill the cooling system. Our partners will collect data and use cookies for ad personalization and measurement. Install the coolant supply and return lines to the air compressor. Ooh no, something went wrong! Compressor All information subject to change without notice. Are you sure you want to delete your template? Recommended Hyundai D4DD engine manual. Ensure that the air compressor retainer is installed on the coolant line and is pushed down to lock the lines onto the inlet and outlet ports to the cylinder block, fuel filter module and air compressor. Manual engine ZD30 nissan. Benefits of the Kobelco More information.