How to change a headlight bulb in a ford focus

Changing the dipped beam bulb on the old Mk1 Ford Focus can seem daunting, and I have read different ways of doing it.

Ford's Focus uses a Halogen H7 bulb in its low-beam socket. Open the bonnet and remove the two Torx screws holding the headlight in place, then lift the headlight forward and out of the car. Unplug the wiring connector on the back, then remove the rubber boot weather seal on the back of the headlight. Undo the grey clip holding the headlight bulb in place, then remove the old bulb. Refitting the headlight is the opposite process. Adjusting the headlight aim should be done by professionals to ensure the light doesn't blind oncoming traffic, while also properly illuminating the road in front of the car.

How to change a headlight bulb in a ford focus

Log in. Sign up. JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding. Sort by Oldest first Oldest first Newest first Most reactions. I've never removed the headlights to replace bulbs on the focus. Pass side is easier, no part removal necessary. On the passenger side, remove the rubber boot from the back of the housing, and unsnap the connector from the bulb and pull it out of the way. Then the bulb and ring will just pull out. Reverse the procedure to reinstall On the driver side you may have to remove a few pieces

The instructions are really clear and the pictures help a lot! Note which way around it went on. On the passenger side, remove the rubber boot from the back of the housing, and unsnap the connector from the bulb and pull it out of the way.

The Ford Focus first sprung on the automotive scene in as a personality-laden replacement for the Ford Tempo. One of this car's calling cards is its headlight design. When one of these unique headlights burns out on your Ford Focus, changing it yourself is a simple repair that will save you time and money. Ensure that the headlights on your Ford Focus are off by checking you have turned the headlight control all the way to the off position. Make sure your car is off and the keys are out of the ignition, so the daytime lamps are also off.

The only tool needed to change any of the headlight bulbs in either the driver or passenger side housing is a Torx T star bit screwdriver. Locate the two screws that hold the headlight assembly in place. One screw is near the outer edge and the other is at the inner corner. Remove the two screws by turning them counter clockwise with a Torx T star bit screwdriver. Set the two screws aside in a safe place. Turn over the housing and rest it on the bumper. To avoid scratching the plastic lens or the painted bumper, place a towel in between them. Pull off the rubber dust cap on the rear of the housing to access the base of the old low beam bulb. Pry up the black plastic tab on the electrical connector before sliding it straight off the bottom of the old bulb. If you do get the new bulb dirty, wipe off the glass with an alcohol moistened paper towel.

How to change a headlight bulb in a ford focus

Headlight Size. Select year Headlight Bulb High Beam - These bulbs produce over 12, lumens of pure high-quality light! HIKARI LEDs also have an advanced error-free cooling system to prevent overheating and constant current technology for burning with no filament degradation. The light tracing system precisely mimics the position of the original halogen filament whose driver side is lower, therefore it avoids wasting lumens and glaring others.

Hltv cs go

I found that you need to be quite forceful to get the thing pressed down hard enough to be able to get the clips fully attached. On the passenger side, remove the rubber boot from the back of the housing, and unsnap the connector from the bulb and pull it out of the way. Safely discard the old bulb. The headlight is now only held in by the power connector. Handling little fiddly things bulbs, screws, tools over a complicated engine with lots of deep dark holes is fraught with danger. The loop of the clip passes over the black square bulb connector and wire. And that's all, folks Once the grill is loose, you should be able to lift the headlight unit away. Attach the three bolts for the headlight or two, if you are leaving the one off that is under the car, as I have. The weathershield has a rubber gasket which must be lined up carefully and then compressed in order for the clips to fasten.

Log in.

Once sat correctly, hold in place with a finger whilst closing the metal retaining loop. Loosen one of these or both if removing entirely. Made what would have been a tricky job simple. Super post. This is an older thread, you may not receive a response, and could be reviving an old thread. When tightening that bolt, don't catch the lip of the plastic under the washer, push it out of the way. The Ford Focus first sprung on the automotive scene in as a personality-laden replacement for the Ford Tempo. More by the author:. Align the bulb with the slots in the unit — it will only fit one way. Step 5 Disconnect the bulb from the connector. Align the bulb with the slots in the unit — it will only fit one way. Swivel the wire clip that hold the bulb and connector in place out of the way by turning it to the left. One of this car's calling cards is its headlight design. Attach the three bolts for the headlight or two, if you are leaving the one off that is under the car, as I have. Take the new bulb by the metal housing — do not touch the glass.