How to replace a lawn mower pull cord

Lori Irby loribirby. Posted: Sep 1, I had taken it to the mower shop and they were going to charge me just to tell me how to do it. Sep 4, by Lori Irby.

Eventually, you're lawnmower pull cord will break. Fortunately it's an easy fix. Check out this video on how to fix Few things are more frustrating than going to cut the grass or clear your driveway of snow and ending up with the starter cord in your hand. Eventually, it happens to everyone. When it does, check out this video on how to fix a lawnmower pull cord.

How to replace a lawn mower pull cord

This DIY lawn mower repair guide has instructions for how to replace a lawn mower starter rope. Over time, the starter rope can wear out and eventually break, and the mower won't start. You can replace a broken recoil starter rope with a manufacturer-approved replacement part by following the steps below. Remove the dipstick tube from the engine and plug the hole with a paper towel to keep debris from falling into the engine. Remove the bolts securing the blower housing to the engine and remove the housing from the engine. Turn the rope pulley counter-clockwise 7 times to wind the spring. Align the hole in the pulley with the hole in the housing and insert a screwdriver through the holes to keep them aligned as you work. Thread the new rope through the hole in the housing and pulley. Tie a knot in the rope to keep it from slipping out of the pulley. While holding the rope, remove the screwdriver from the holes in the pulley and housing, and let the rope slowly rewind. Attach the other end of the rope to the starter handle. Feed the rope through the hole in the handle and secure it with another knot. Remove the paper towel from the dipstick opening, slide the dipstick tube into the engine and secure it with the screw. Main causes: engine needs tune up, dirty or clogged carburetor, damaged flywheel key…. Main causes: uneven wheel height settings, damaged wheel, dull or damaged cutting blade….

Articles and videos common to all walk-behind mowers. Repair difficulty.

.

At some point, all household maintenance tools are subject to wear and tear, and your lawn mower is no exception. A broken lawn mower pull cord is a pretty common problem. And fortunately, it is easy to get done DIY. When a pull cord is broken, it means that the starter rope has detached from the rest of the cord. The starter rope is the visible part of the cord. You can access it from outside of the mower. Make sure you replace it if it breaks. Usually mower pull cords break from regular wear and tear, but your cord may have broken because:.

How to replace a lawn mower pull cord

September 13, by Marjorie R. To replace a lawn mower pull cord, follow these steps: First, remove the recoil assembly cover and pull out the old cord. Then, attach the new cord to the recoil pulley, wind it around, and secure the end. Finally, reattach the recoil assembly cover, and your lawn mower is ready for use! Whether your pull cord has snapped or is simply worn out, replacing it is a straightforward process that can be done with basic tools and a little bit of patience. Read on to learn how to replace a lawn mower pull cord and get your mower running smoothly again. Understanding the importance of a working pull cord is essential for replacing a lawn mower pull cord. Understanding the importance of a working pull cord not only ensures smooth operation but also saves you from potential frustration and inconvenience.

Cappuccino motor

Share: Link copied to clipboard. Remove the paper towel from the dipstick opening, slide the dipstick tube into the engine and secure it with the screw. This DIY lawn mower repair guide has instructions for how to replace a lawn mower starter rope. Reconnect the spark plug wire. Disconnect the spark plug wire. View the answer I have this problem too Subscribed to new answers. Remove the bolts and the pull cord unit should lift right off. December 9, Posted: Jan 25, Options Permalink History. Some repairs should only be performed by a qualified technician. Learn about Sears Technical Institute and the advanced technical content being developed for aspiring appliance techs. Remove the screws securing the engine cover to the engine. Remove the dipstick tube. Then, click "Attach comment to this post" to move it.

With perfect weather, you plan to go out to give your lawn a nice trim. You use a push mower that has never let you down in all these years.

Why won't my lawn mower move? Continue turning the recoil, making sure to apply enough pressure to prevent the spring from releasing and bloodying your knuckles. Use the proper tools and safety equipment noted in the guide and follow all instructions. Inspect the starter pulley and remove any remaining starter rope. Position the engine cover on the engine and screw it into place. View all. This seals the fibers and makes it much easier to thread the cord. Position the engine blower housing on the engine and bolt it into place. Add additional length as needed if the cord broke farther from the handle. Chosen Solution. How To Videos Share: Link copied to clipboard.