Ipod nano 1 battery

I recently found an old iPod Nano 1st Generation that was sitting in a drawer, ipod nano 1 battery, collecting dust since around or When it was in use, it was slightly damaged with a small dent on one side of the back. I also noticed the back was slightly coming off on the opposite side of the dent, but I assumed it was just because of the dent.

Enter your email address below, and we will notify you when this product is back in stock. This iPod nano 1st Gen replacement battery is what you need to bring your dead iPod back to life! Battery degradation is an inevitable part of your iPod's lifespan — extend it with this new replacement battery compatible with the first generation iPod nano. Then use your device until it shuts off due to low battery. This replacement battery may be a slightly more snug fit than the original due to a small variation.

Ipod nano 1 battery

The rear panel is secured to the front case by eleven clips permanently attached to the rear panel. These clips lock onto small tabs machined into the front case. To free the tabs, they must be pushed down and away from the iPod's case. Note the location of all tabs on the rear panel. When using an iPod opening tool to free the rear panel, be sure to work the tool at the location of these clips. Opening the iPod can be challenging. Don't get discouraged if it takes you a few tries before the iPod is opened. Insert the large iPod opening tool into the seam between the front case and rear panel of the iPod, below the dock connector. Run the tool back and forth to create an opening. The tool's edge should point toward the rear panel to prevent any accidental scratching of the aluminum front case. Insert a small iPod opening tool into the seam on the Hold button side of the iPod, with the edge of the tool pointing toward the rear panel. The large iPod opening tool is no longer needed to gain access to the left side of the iPod.

To open the solder holes, open a safety pin and push it against the solder blocking the hole. Fast shipping Same day shipping if ordered by 1PM Pacific. Posted on Aug 10, AM.

.

Arrange to mail your product directly to Apple. We can replace your iPod battery for a service fee. We replace cracked screens for a fee. Accidental damage isn't covered by the Apple warranty. If you go to another service provider, they can set their own fees, so ask them for an estimate.

Ipod nano 1 battery

The rear panel is secured to the front case by eleven clips permanently attached to the rear panel. These clips lock onto small tabs machined into the front case. To free the tabs, they must be pushed down and away from the iPod's case. Note the location of all tabs on the rear panel. When using an iPod opening tool to free the rear panel, be sure to work the tool at the location of these clips. Opening the iPod can be challenging. Don't get discouraged if it takes you a few tries before the iPod is opened. Insert the large iPod opening tool into the seam between the front case and rear panel of the iPod, below the dock connector. Run the tool back and forth to create an opening.

Charles schwab careers

This was the third battery for my iPod, so the desoldering step took a fair amount of time. To aid in soldering the new battery, be sure the solder pad holes are clear of solder. Repair with confidence All our products meet rigorous quality standards and are backed by industry-leading guarantees. Rotate the battery toward the logic board and place it flat in its void, bending the cables as necessary. Small - px Medium - px Large - px. Assembly contents. For all newbies, make sure that your soldering spots are neat and clean. In this step, you will solder the battery leads to the solder pads on the logic board. Solder the other two battery leads in the same fashion, taking care not to bridge any of the connections together. Hold wire until solder has set. All our products meet rigorous quality standards and are backed by industry-leading guarantees. To keep the leads in place, it may be helpful to first bend the battery leads into their final shape, then insert the stripped ends into the holes. I am not very experienced with soldering, so I practiced on a little blinking christmas tree kit before attempting this, and I think that was useful. At the same time, heat the same solder pad from the other side of the logic board.

This instructable goes over how to change the battery in your 1st Gen Ipod Nano. This ipod was found in the junk pile at instructables with a bloated battery. Next time your friend throws out their old ipod, try to fix it up!

To free the tabs, they must be pushed down and away from the iPod's case. Much simpler and less risk. Time Required: 40 minutes - 2 hours. Rotate the battery out of the iPod and lay it next to the iPod. The instructions were clear and helpful. I was wondering if apple still could replace the battery of the iPod or if they no longer do that because it is so old? When using an iPod opening tool to free the rear panel, be sure to work the tool at the location of these clips. No that's what I call environmental awareness! I am not very experienced with soldering, so I practiced on a little blinking christmas tree kit before attempting this, and I think that was useful. I have a 16G, 6 generation ipod touch that I purchased in In order to avoid damage, lift the solder tip off the connection as soon as the solder melts and the lead slides out.