Ipod nano battery replacement

Front Page. How Tos.

However, a variety of more affordable third-party services also are available. Third-parties offer battery replacement services for considerably less than Apple charges and often sell "longer runtime than stock" batteries for self-installation as well. If you are not sure which iPod nano you have, one way to externally identify these models is via a unique model number on the back of the device. These models also can be differentiated by serial number with Everyi. Like the model number, the serial number is toward the bottom on the back of the device or under the "teeth" on the clip and also is available when plugged into a computer on the "Summary" tab in a modern version of iTunes among other methods. In addition to its serial number, Everyi.

Ipod nano battery replacement

Arrange to mail your product directly to Apple. We can replace your iPod battery for a service fee. We replace cracked screens for a fee. Accidental damage isn't covered by the Apple warranty. If you go to another service provider, they can set their own fees, so ask them for an estimate. We'll inspect your product when we receive it. If additional damage is found, you could pay an additional fee. Hardware service may no longer be available for some older products. See obsolete and vintage products. All fees are in U. A shipping fee will be added if we need to ship your iPod. The Apple Limited Warranty covers your iPod and the Apple-branded accessories that come in the box with your product against manufacturing issues for one year from the date you bought them. Apple-branded accessories purchased separately are covered by the Apple Limited Warranty for Accessories.

All fees are in U. This was the part where I failed because afterwards I wasn't able to insert the battery plus the iPod circuit board inside its case again and ended it breaking it.

The iPod Nano 6th Generation battery is not a plug-and-play battery. This process requires delicate desoldering to remove the old battery. Use a heat gun or hair dryer to soften the adhesive securing the perimeter of the front panel assembly to the outer case. Be careful not to overheat the front panel assembly, as it may result in damage to the LCD. While the front panel is still warm, use the edge of an opening tool to pry it from the headphone jack side of the front panel assembly out of the Nano. Do not attempt to pry out the front panel assembly from, or insert the opening tool into the left side of the display, as the display data cable is right underneath and may be damaged in the process.

Replacing the battery requires a fine tip soldering iron and is a difficult job that only experienced solderers should attempt. Insert the edge of an iPod opening tool into the gap between the outer case and the top bezel. At this point the hold switch slider is free and may fall. Be careful not to lose it. Remove the two angled Phillips screws from the two corners of the display retainer. Do not rotate the display retainer about the top edge of the display, as it is attached to a thin steel bracket that is easily broken. Do not forcefully remove the display retainer, as the hold switch cable is liable to snap. Slide the display out of the Nano. It will move about.

Ipod nano battery replacement

Carefully insert an iPod opening tool in the seam between the metal casing and white plastic top. Lift the top bezel off the iPod. It's glued on using a mild adhesive, so some force may be required. When removing the bottom bezel, be sure not to bend the plastic surrounding the dock connector. Carefully insert an iPod opening tool in the seam between the metal casing and white plastic bezel. Lift the bottom bezel off the iPod. One Phillips screw with a smaller head near the side of the iPod.

Wholehearted crossword clue

Rene Jeddore - Mar 4, Reply. You're Finished! Remove the single 1. Step 3. Author with 13 other contributors. Small - px Medium - px Large - px. These two options are detailed below. When reassembling, ensure the click wheel cable is toward the front of the Nano and not in the grooves on the side. To reassemble, you can use the double-sided tape found here. Add Comment. Jan 29, Step 10 Removing old wires entirely. The stain on one is about 1cm long, and another one just developed a smaller stain at the end of this summer. Remove the two angled Phillips screws from the two corners of the display retainer.

Arrange to mail your product directly to Apple. We can replace your iPod battery for a service fee.

Yes - you flick the White bit. Arrange to mail your product directly to Apple. Succeeded on the next day, but now pushing in the display feels weird: The way they do it in videos makes it seem so simple and easy, but mine isn't coming off and I'm afraid to use more pressure because pushing it makes the black bits appear onto the screen again due to the battery pushing against it Be careful not to lose it. Small - px Medium - px Large - px. Force may be required to remove the battery from the logic board. I have acquired these iPods in a used condition within the last 1,5 years or so, because I wanted to keep different types of data on separate iPods and not run out of space. Step 7. Use an opening tool to disconnect the display data and digitizer cable connectors up from their sockets on the logic board. To reassemble your device, follow these instructions in reverse order. These models also can be differentiated by serial number with Everyi. Read the Apple Limited Warranty. But I'm worried about the swollen batteries on the other two ; How dangerous is it to operate on them when in such condition? For a better experience, please enable JavaScript in your browser before proceeding. Add Comment.